C4L-6) 1969 70 71 72 73 Mercury Cougar Sequencer Turn Signal Kit (Incandescent) For Sale
C4L-6) 1969 70 71 72 73 Mercury Cougar Sequencer Turn Signal Kit (Incandescent)
Click HERE for more information about this vehicle.
California Proposition 65:WARNING:This product has not been tested for chemicals known to the State of Californiato cause cancer and birth defects or other reproductive harm. For more informationgo to www.p65warnings.ca.gov
All parts are new aftermarket replacement parts manufactured by Cougars Unlimited LLC and come with a 2-year limited factory warranty. They are replacement parts to be used to replace the original Ford parts used in there sequencing tail light systems on models that originally came with sequencing tail lights. They are made to plug and play into the original mounting and wiring harness. They are not designed to be used to convert non-sequencing tail light systems to sequencing tail lights.
You are purchasing aCougars Unlimited LLC Kitused to replace theoriginal MercuryCougar sequencing turn signal system usingincandescence bulbs.
Included parts are:
One C9WY-13A366-ALSequencer Flasher board (Note:Compatible with either LED orIncandescentbulbs)
and
19691970 *19711972 1973Mercury Cougar
Replaces:Turn signalSequencer Flasher board and thermal flasher can
Flasher can options:
When usingincandescencebulbs then use Cougars Unlimited LLCDOWY-13350-ARincandescenceElectronic Flasher can, included in this purchase.
If converting to LED bulbs using this sequencer board then you will have to purchase theCougars Unlimited LLCDOWY-13350-L LED Flasher can, NOT included with this purchase.Cougars Unlimited LLC strongly recommends using WCCC1157RPR (Red for rear) LED bulbs and WCCC1157YPR (Yellow for front) LED bulbs. They have a built in current limiting diode. This stops the reverse current flow that causes sequential turn signal systems to malfunction.
This sequencer does not come with the black case and you will need to reuse the original. Simply open it up and remove the old circuit card and replace it with the new one. The connectors will match up to your existing harness. No soldering or wire crimping necessary.
You might need this kit if your Symptoms are:
One or more lights not flashing
Inner lights only flashing
All lights on but not flashing
All lights flash together
Outer light on both sides not flashing or flashing very dim
*Note: On some model’s special connectors were used on the 1971 Cougars made between 5/17/71 and 1/1/72. You will have to send the old sequencer to us so we can reuse the connectors and solder them on to the new sequencer. There is no charge for this.
Extensive research has been put into the choosing of proper connectors, gauge of wires, industrial grade connectors and electronic components. They are nice! All aspects of the manufacturing process from design to testing are overseen by an electronic engineer with over 40 years of experience, as a result these units the most robust and reliable units on the market.
Cougars Unlimited LLC manufactures sequential turn signal systems for 1967-1973 Cougar and 1965-1971 Thunderbird and 1968-1970 Mustang Shelby. Since 1981 Cougars Unlimited has been the source for the electronic sequencers used to replace the failure-prone mechanical motor driven turn signal sequencers. Member of the Cougar Club of America since 1981 and a founding member of the Cougar Club of New Mexico.
40 years of service / Thousands sold to satisfied customers
Parts Chart BARGANSPOT (an eBay store) www.barganspot.com
(All parts manufactured by Cougars Unlimited LLC)
1969 Cougar
Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)
Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)
Flasher can electronic, LED systems - C6L) DOWY-13350-L (LED bulbs)
TURN SIGNAL SWITCH - WITH TILT – C48) C8SZ-13341-BR (*LED bulbs only)
TURN SIGNAL SWITCH - WITHOUT TILT – C43) C9AZ-13341-BR (*LED bulbs only)
Headlight Switch with vacuum control - C73) C8WY-11654-AR
Starter Solenoid Pigtail Set Harness repair kit - C83) C9WB-14488-P
Harness REPAIR kit – (Harness side, these plug into sequencer) -(C33 C9WY-13H366-AR
Front Turn Signal Bezel Harness pigtail (1 pair) C77B) C8WB-13234-AR
Dash to Engine Gauge feed - 390/427/428 – C63) D0AZ-14289-AR
Dash to Engine Gauge feed - 351W - C62) D4AZ-14289-RR
XR7 \"Alternator wiring harness” - with ammeter – C30) C9ZZ-14305-SR
Standard \"Alternator wiring harness” - without ammeter – C29) C9WY-14305-GR
Tilt column wiring harness – and flyaway – C28) C9ZZ-3D568
Standard “Dash Panel to Headlight” Wiring Harness - C25) C9WY-14290-AR
XR7 “Dash Panel to Headlight” Wiring Harness – C13) C9WY-14290-LR
Standard “Tail Light Wiring Harness with Sockets” – C76/C82) C9WY-14405-RR/C8WB-14406-BR
XR7 “Tail Light Wiring Harness with Sockets” – C76) C9WY-14405-RR
1970 Cougar
Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)
Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)
Flasher can electronic, LED systems - C6L) DOWY-13350-L (LED bulbs)
TURN SIGNAL SWITCH - WITH TILT – C46) D2AZ-13341-DR (*LED bulbs only)
TURN SIGNAL SWITCH - WITHOUT TILT – C41) D2AZ-13341-CR (*LED bulbs only)
Headlight Switch with vacuum control - C73) C8WY-11654-AR
Starter Solenoid Pigtail Set Harness repair kit - C83) C9WB-14488-P
Harness REPAIR kit – (Harness side, these plug into sequencer)-(C33 C9WY-13H366-AR
Front Turn Signal Bezel Harness pigtail (1 pair) C77B) C8WB-13234-AR
Dash to Engine Gauge feed - 351C 2V/4V- C64) D0ZZ-14289-AR
Dash to Engine Gauge feed - 390/427/428 – C63) D0AZ-14289-AR
Dash to Engine Gauge feed - 351W - C62) D4AZ-14289-RR
XR7 \"Alternator wiring harness” - with ammeter – C69) DOZZ-14305-CR
Standard \"Alternator wiring harness” – without ammeter – C68) DOWY-14305-CR
Side Marker LED Adapter Kit - C36) DOWY-15A434-LSM
1971 Cougar
Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)
Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)
Flasher can electronic, LED systems - C6L) DOWY-13350-L (LED bulbs)
TURN SIGNAL SWITCH - WITH TILT – C46) D2AZ-13341-DR (*LED bulbs only)
TURN SIGNAL SWITCH - WITHOUT TILT – C41) D2AZ-13341-CR (*LED bulbs only)
Harness REPAIR kit – (Harness side, these plug into sequencer)-C33) C9WY-13H366-AR
Dash to Engine Gauge feed - 351C 2V/4V- C21) D1OZ-14289-AR
XR7 \"Alternator wiring harness” - with ammeter – C71) D1ZZ-14305-BR
Standard \"Alternator wiring harness” – without ammeter – C70) D1OZ-14305-BR
Side Marker LED Adapter Kit – C78) D1WY-15A434-LSM
1972 Cougar
Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)
Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)
Flasher can electronic, LED systems - C6L) DOWY-13350-L (LED bulbs)
TURN SIGNAL SWITCH - WITH TILT – C46) D2AZ-13341-DR (*LED bulbs only)
TURN SIGNAL SWITCH - WITHOUT TILT – C41) D2AZ-13341-CR (*LED bulbs only)
Harness REPAIR kit – (Harness side, these plug into sequencer)-(C33 C9WY-13H366-AR
1973 Cougar
Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)
Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)
Flasher can electronic, LED systems - C6L) DOWY-13350-L (LED bulbs)
Harness REPAIR kit – (Harness side, these plug into sequencer)-(C33 C9WY-13H366-AR
*NOTE: TURN SIGNAL SWITCH – All turn signal switches sold by Cougars Unlimited LLC are for use with LED bulbs only. The reason for this is applicable vehicles are now over 50 years old the current that sequencing systems draw have greatly increased over time. This is because of the original wiring harnesses and connectors are deteriorating increasing the resistance. Higher the resistance the higher the current draw across the switch. The current is now so high on most vehicles that it exceeds the ratting of the switches, causing them to prematurely fail. The only solution is to convert to LED bulbs, they draw far less current. On vehicles that have converted to LED the turn signal switches are not failing. The only other solution is to replace the complete wiring harness which is expensive, and in most cases not possible.
When converting to LED bulbs Cougars Unlimited LLC strongly recommends using WCCC1157RPR (Red for rear) LED bulbs and WCCC1157YPR (Yellow for front) LED bulbs. They have a built in current limiting diode. This stops the reverse current flow that causes sequential turn signal systems to malfunction.
